-
L293D Motor Driver/Servo Shield for Arduino
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- Pull down resistors keep motors disabled during power-up
- Arduino reset button brought up top
₹140₹250In stock
-
BTS7960 43A H-Bridge High Power Stepper Motor Driver Module
- Input voltage(V): 6 – 27.
- Maximum current(A): 43.
- Input level(V): 3.3 – 5.
- Duty cycle: 0 – 100%.
₹280₹550In stock
-
A4988 Stepper Motor Driver Module
- Supply Voltage: 8-35 VDC.
- Current: 1.0A (no heatsink)
- Current: 2.0A (with heat-sinking)
- logic input: 3 – 5.5V
₹80₹110In stock
-
L298N 2A Dual Motor Driver Module With PWM Control
- Heatsink for better performance.
- Power-On LED indicator.
- Double H bridge Drive Chip: L298N.
- Operating Voltage (VDC): 5~35
- Peak Current (A): 2
- Continuous Current (A): 0-36mA
- of Channels: 2
₹130₹180In stock
-
Pro Micro 5V 16M Mini Leonardo Microcontroller Development Board
- ATMEGA32U4 running in 5V / 16MHz
- Support Arduino IDE V1.0.1
- Micro USB interface programming on the board
- Four 10-bit ADC pin
- 12 digital I / O (5 PWM capability)
- Rx and Tx hardware serial connection
₹550₹620In stock
-
USB to RS485 Converter Adapter
- Fully compliant USB 2.0 standard, backward compatible with USB1.1
- Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive
- Supports Plug, Play and hot-swap (USB side)
- Better than using CH341D chip or similar chip to support the laptop USB port.
- Communication distance up to 1.2KM
₹120₹150In stock
-
PL2303 PL2303HX USB To TTL(Serial) Converter Module – 5 Pin
- Fully Compliant with USB Specification v2.0 (Full-Speed)
- Supports RS-232 serial interface
- On chip USB 1.1 transceiver, 5V to 3.3V regulator
- Two data transmission LEDs that indicate data transfer status in real time
- Has a 500mA self-recovery fuse for safety
₹85₹120In stock
-
5V 4 Channel Relay Module with Optocoupler
- of Channel: 4
- Trigger Level: LOW
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
₹140₹200In stock
-
5V 2 Channel Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage (3.3V – 5V)
₹85₹120In stock
-
5V 1 Channel Relay Module
- Trigger Voltage: 5 VDC
- Trigger Level: LOW
- Maximum Switching Voltage: 250VAC@10A; 30VDC @10A
- Single Pole Double Throw (SPDT) Configuration
- Power supply indicator LED
₹40₹70In stock
-
Micro HDMI Male to HDMI Female Adapter for Raspberry Pi
- Micro HDMI Male to HDMI Female
- Gold plated connectors for flawless signal transference
- CE and ROHS Compliant
- For the Raspberry Pi
₹60₹80In stock
-
WeMos D1 R2 WiFi ESP8266 Development Board
- Microcontroller: ESP8266EX
- Operating Voltage: 3.3V
- Digital I/O Pins: 11
- Analog Input Pins: 1
- Based on the ESP-8266EX.
- Arduino Compatible, you can use it on Arduino IDE.
- NodeMcu Compatible
₹350₹380In stock
-
Wemos D1 Mini ESP8266 NodeMcu Lua WIFI IOT Development Board
- Driver IC: CH340
- 11 digital input/output pins
- 1 analog input (3.2V max input)
- Micro USB connection
- Use BRT (Bias Resistor Transistor), easier into flash mode.
- Compatible with Arduino
- Compatible with NodeMCU
- Compatible with MicroPython
₹165₹27039% offIn stock
-
NodeMcu ESP8266 V3 Lua CH340 Wifi Dev. Board
- Uses CH340G instead of CP2102.
- Wireless 802.11 b/g/n standard
- WiFi at 2.4GHz, support WPA / WPA2 security mode
- Support UART / GPIO data communication interface
- A great set of tools to develop ESP8266
- Lowest cost WI-FI
- FOR Arduino like hardware IO
₹180₹30040% offIn stock
-
USB To UART/ESP8266 Adapter Programmer For ESP-01 WiFi Modules With CH340G Chip
- Driver Chip: CH340G
- Supports all basic windows versions.
- Working voltage: 4.5V – 5.5V
- Working current: 300mA
₹100₹120In stock
-
MT76813DBI ESP8266 Serial WIFI Wireless Gain Antenna
- Radome material: polyurethane
- Flexible cable
- Stable signal
- Best for indoor applications.
₹70₹80In stock
-
Micro SD Card Reader Module
- Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board
- Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm
₹40₹80In stock
-
FS1000A 433mHz Transmitter Receiver RF Radio Module
- Wide input supply (2.5 V to 12V)
- Easy to integrate (V+, GND, and Data)
- The device in deep sleep mode when Data pin is grounded
- Very small dimension.
₹100₹120In stock
-
Infrared IR Wireless Remote Control Module Kit
- Battery: CR2025 160mAh button battery
- Effective angle: 60°
- Sticking material: 0.125mmPET
- Static current: 3uA – 5uA
- Dynamic current: 3mA – 5mA
₹90₹105In stock
-
3.3V Adapter Board For 24L01 Wireless Module
- It can be used with NRF24L01 wireless module
- Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
- Small power on SMD LED indicator
- On-Board Voltage Regulator
₹50₹70In stock
-
ESP-01 ESP8266 Serial WIFI Transceiver Module
- 11 b/g/n Standards
- Wi-Fi Direct (P2P), soft-AP
- 1MB Flash Memory
- Integrated low power 32-bit CPU could be used as an application processor
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
₹120₹170In stock
-
Ai Thinker LoRa Ra-02 SX1278 433MHz Wireless Spread Spectrum Transmission Module
- Communication distance: 15KM
- Sensitivity: down to -148dBm
- Programmable bit rates: up to 300kbps
- RSSI dynamic range: 127dB
₹430₹490In stock
-
2.4GHz NRF24L01+PA+LNA SMA Wireless Transceiver Antenna
- Voltage: 3-3.6V (recommended 3.3V) V.
- Maximum output power: +20dBm.
- Power-down mode current: 4.2uA.
- Operating Range: 1Km
- Antenna Gain (peak): 2Dbi.
₹180₹450In stock
-
SanDisk 64GB Micro SD Card – Class10
- Memory Size: 64 Gigabyte
- Card Type: Micro SD
- Speed: up to 98MB/s
- Class: 10
- High-speed Card
₹550₹850In stock
-
SanDisk 128GB Micro SD Card – Class10
- Memory Size: 128 Gigabyte
- Card Type: Micro SD
- Speed: Up to 120MB/s transfer speed
- Class: 10
- High-speed Card
₹1,100₹1,560In stock
-
SanDisk 32GB Micro SD Card – Class10
- Memory Size: 32 Gigabyte
- Card Type: Micro SD
- Data transfer Speed: up to 98MB/s
- Class: 10
₹429₹550In stock
-
ESP8266 NodeMCU CP2102 Board
- Operating Voltage: 5V
- Input Voltage: 7-12V
- Digital I/O Pins (DIO): 16
- Analog Input Pins (ADC): 1
- UARTs: 1
- SPIs: 1
- I2Cs: 1
- Flash Memory: 4 MB
- SRAM: 64 KB
- Clock Speed: 80 MHz
₹275₹38529% offIn stock
-
RC522 RFID 13.56MHZ Reader Writer Module / MFRC-522 Module with RFID Tag
- Operating Voltage: 3.3V
- Operating Current: 13-26 mA
- Operating Frequency: 13.56MHz
- Communication Interface: SPI protocol
- Reader Distance: less than 5cm
- Data Transfer Rate: 10Mbit/sec(max)
₹90₹150In stock
-
SIM800L GSM GPRS Module Quad-band TTL Serial Port with antenna
• 2G Quad-band 850/900/1800/1900MHz
• Receive and make calls using the speaker and microphone outputs
• Receive and send SMS
• GPRS multi-slot class12 connectivity: max. 85.6kbps(download/upload)
• Operating Voltage range 3.4V ~ 4.4V
• Supports A-GPS
• Low power consumption, 1mA in sleep mode
• Micro SIM Card Slot₹270₹350In stock
-
RF 433MHz Wireless Transmitter Receiver Module (Red)
Features :
- Low Power Consumption.
- Easy For RF-based Application.
- Wide Operating Voltage (1.5-5v)
- ASK Modulation
₹140₹220In stock
-
Raindrops Detection Sensor Module
- Working voltage 5V
- Output format: Digital switching output (0 and 1), and analog voltage output AO
- Potentiometer adjust the sensitivity
- Uses a wide voltage LM393 comparator
₹50₹100In stock
-
Voltage Detection Sensor Module (0-25V)
Input Voltage range: DC 0 to 25 V
Voltage detection range: DC 0.02445 V to 25 V
Analog Voltage resolution : 0.00489 V
Dimensions: 28 x 14 x 13 mm(LxWxH).
Weight: 4 gm.₹35₹70In stock
-
Ultrasonic Sensor Module – HCSR04
- Operating Voltage: 5 V
- Sonar Sensing Range: 2-400 cm
- Sensing Range: 450 cm
- Frequency: 40 kHz
₹65₹8019% offIn stock
-
LDR Module – Photosensitive Light-Dependent Sensor
- Operating Voltage: 3.6V to 5V DC
- Adjustable potentiometer to adjust the sensitivity
- LM393 comparator IC for digital output
- Easy to install thanks to bolt hole provided
- Digital Output
₹35₹60In stock
-
PIR Motion Detection Sensor – HC SR501
- Wide Working Voltage Range: DC 4.5V- 20V
- Current Drain: <60uA
- Detection Angle: <140°
- Detection Distance: 3 to 7m (can be adjusted)
- Blockade time: 2.5s (Default)
- Work temperature: -20-+80°C
₹70₹120In stock
-
IR Sensor Module – Infrared Proximity Sensor
- 5VDC Operating voltage
- I/O pins are 5V and 3.3V compliant
- Built-in Ambient Light Sensor
- 20mA supply current
- Mounting hole
- Adjustable Range Detection
- LED Indicators
₹40₹5020% offIn stock
-
Flame/Fire Sensor Module for digital Output
- Output Channel: 1
- Power Supply: 3.3/5V
- Built in a potentiometer for sensitivity control.
₹40₹100In stock
-
UNO SMD Version Board ATMEGA328 (Without Cable)
- Arduino Uno R3 SMD version
- Based on Atmel AVR Atmega328-AU MCU
- Clock: 16 Mhz
- Flash: 32 KB
- SRAM: 2 KB
- EEPROM: 1 KB
₹270₹49946% offIn stock
-
UNO DIP Version ATMEGA328 Board (Without Cable)
- Arduino Uno DIP Version Compatible Module
- 32 KB Flash
- 2 KB SRAM
- 1 KB EEPROM
- Frequency: 16 Mhz
₹450₹70036% offIn stock
-
DHT11 Temperature And Humidity Sensor Module
- Power Supply: 3.3~5.5V DC
- Output: 4 pin single row
- Measurement Range: Humidity 20-90%RH, Temperature 0~50?
- Accuracy: Humidity +-5%RH, Temperature +-2?
- Resolution: Humidity 1%RH, Temperature 1?
₹65₹102In stock
-
HDMI to VGA Converter Adapter Cable
- Input: HDMI Male
- Output: VGA Female
- Power Supply: No external power required
- Resolution: 720/1080p
- Color : Black or White
₹200₹300In stock
-
5MP Raspberry Pi Camera Module With Cable
Feature :
1. Use for: Raspberry Pi 4 Model B / 3B+ / 3B
2. 5 megapixels
3. Support max 1080P resolution
4. Mini size, easy to place and use.
Package list:
1 x 5MP Camera, 1 x 15cm Camera Cable
₹285₹450In stock
-
CNC shield V3 for Engraving Machine 3D Printer
Specification:
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
₹140₹350In stock
-
Arduino 1602 LCD Board Keypad Shield
- Operating Voltage: 5V
- 5 Push buttons to supply a custom menu control panel
- RST button for resetting Arduino program
- Integrate a potentiometer for adjusting the backlight
- Expanded available I/O pins
₹220₹300In stock
-
PRO MINI ATMEGA328P
- Microcontroller: ATmega328P
- Circuit Operating Voltage: 5V
- Clock frequency: 16MHz.
- Support 9V battery.
₹250₹450In stock
-
Nano CH340 Board (Without Cable)
- Operating Voltage (logic level): 5V
- With Soldered Connector
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
₹230₹450In stock
-
Mega 2560 Board ATMEGA16U2 (Without Cable)
- Operating Voltage: 5 V
- Input Voltage (recommended): 7-12 V
- Input Voltage (limit): 54 (of which 15 provide PWM output)
- Digital I/O Pins: 16
- Analog Input Pins: 20 mA
₹1,250₹1,800In stock
-
Lilypad 328 ATmega328P
- Microcontroller : ATmega168 or ATmega328V
- Operating Voltage : 2.7-5.5 V
- Input Voltage : 2.7-5.5 V
- Digital I/O Pins : 14
- PWM Channels : 6
- Analog Input Channels : 6
₹500₹700In stock
